Heating & cooling service and free initial visitF280 scope inquiry

Heating, cooling, heat pumps & rebates

Replace the equipment.
Rethink the size.

Don’t simply replace what is already installed. Measure the home and calculate what it actually requires before choosing the next furnace, air conditioner or heat pump.

Discuss your home comfort
Concept illustration of a measured interior home model used to explain geometry capture
House geometry is an input. Better sizing is the goal.

The house comes first

Three different questions.
One better decision.

The old nameplate tells us what is installed. A load calculation helps establish what the home requires.

01 / Existing equipment

What is installed?

64,000Btu/h furnace output

Nameplate and verified specifications establish the existing system’s capacity.

02 / Calculated requirement

What does the house need?

42,000Btu/h design heating load

House geometry, enclosure and design conditions establish the heating requirement. Cooling is calculated separately.

03 / Suitable options

What equipment fits?

  • Furnace capacity & modulation
  • AC capacity & cooling load
  • Heat-pump performance & backup
  • Duct/distribution suitability

A shortlist based on verified model capacities and your home’s requirements.

Illustrative numbers only. The 64,000 and 42,000 Btu/h values are not measurements from your home or a replacement-size recommendation. Final equipment selection considers both loads, performance and installation requirements.

Measure → calculate → select

Know why an option
belongs on your shortlist.

A bigger unit is not automatically the right answer to an uncomfortable room.

We connect the load result with equipment performance and what your distribution system can reasonably support.

Explore whole-house and room-by-room F280 scope
House assessment & calculated loads

Capture actual geometry and relevant enclosure inputs. Use whole-house/block or room-by-room CSA F280 calculations where appropriate. We explain whether a preliminary plan or a formal CSA F280 calculation is appropriate for your project.

Existing equipment versus calculated need

Compare verified furnace output and cooling capacity with the home’s calculated requirement. Consider completed or planned insulation upgrades that may change the requirement.

Heat-pump suitability & performance

Check model-level capacity at relevant outdoor temperatures, controls, backup heat, matched equipment and the sizing approach required by the rebate pathway.

Basic duct & distribution screening

Review accessible duct, return and filter dimensions, distribution layout and comfort complaints. Identify possible constraints and when an HVAC contractor should perform further measurements. This is a screen, not a claim of measured delivered airflow.

Equipment selection & quote review

Review furnace, AC or heat-pump options against the same house requirements. Clarify models, scope, accessories and exclusions before an installation recommendation is finalized.

Current HRS heat-pump rebates

The right number depends
on where you’re starting.

Existing heating fuel, system type and ownership change the offer. A participating contractor must obtain approval before installation.

Existing primary heating / ownershipCold-climate air sourceGround source
Enbridge natural gas • owned$500 / eligible ton
Up to $2,000
$3,000 • full system
Electricity, oil, propane or wood • owned$1,250 / eligible ton
Up to $7,500
$2,000 / eligible ton
Up to $12,000
Eligible fuels • rental$500 / eligible ton
Up to $2,000
$3,000 • full system

Source: official HRS heat-pump page and stream requirements, checked October 1, 2026. These are separate from Assessment Stream totals.

Illustrative potential rebate$1,500

$500 per ton for 3 tons of eligible heating capacity, up to $2,000.

A “ton” describes heating capacity. Use the eligible heating rating confirmed for the equipment: air source uses the listed heating rating at 8.3°C; ground source uses the applicable loop heating capacity. These inputs do not establish eligibility or size equipment for your home.

Eligibility and installation details

Your current heating system, equipment choice and installation plan affect which rebates may fit. We check the details with the participating contractor before work begins.

The contractor handles the required pre-approval and final documents. We will explain the available path and next steps before you commit.

Why the assessment planner does not add this rebate

Space-heating heat pumps have their own application and pre-approval process. They do not count as an upgrade toward the Assessment Stream two-upgrade minimum or three-upgrade bonus. We keep the totals separate so an attractive combined number does not hide different eligibility requirements.

Before you choose the model

Let’s understand the requirement.

Start with your home, existing equipment or a quote you want reviewed.

Discuss your options

Verified program references